[. . . ] Specifications UMATM 752 MIXER/AMPLIFIER Specifications Rated output power: 75 Watts Output regulation: Direct out: Transformer out: <0. 5 dB <1. 0 dB Pre out: Inputs: Channel 1: 1 V nom. ; +21 dBu max. , at 100 Ohms Mic 1 mV at 1. 8 k Ohms (XLR or screw terminals) Tel 100 mV at 20 k Ohms (Screw terminals) Mic 1 mV at 1. 8 k Ohms (Screw terminals) Line 100 mV at 20 k Ohms (Screw terminals) Line 100 mV at 20 k Ohms (Screw terminals) Line 100 mV at 20 k Ohms (Screw terminals) Stereo 316 mV (-10 dBV) at 4. 0 k Ohms (RCA jacks) 1 Volt at 20 k Ohms ±10 dB at 100 Hz ±10 dB at 10 kHz Frequency response: Power Amplifier: ±0. 5 dB, 20 Hz to 20 kHz, direct out ±1. 0 dB, 50 Hz to 20 kHz, transformer out Preamplifier: ±1. 0 dB, 20 Hz to 20 kHz THD: Power Amplifier: Preamplifier: 0. 05% (1 kHz) 0. 10% with nominal gain settings Channel 2: Channel 3: Channel 4: Power bandwidth (±3 dB): Direct out: <10 Hz to 70 kHz Transformer out: 30 Hz to 40 kHz Signal/noise: (22 Hz -- 22 kHz) typical All controls CCW: -100 dB All controls nominal (5): -90 dB Level controls CCW and master level CW: -80 dB Outputs: Direct out: XFMR: Ch. 4 out: 4 Ohms Balanced 8 Ohms (25 V), 70 V, 100 V 1 V nom. , +21 dBu max. [. . . ] When in the microphone mode, 24 Volt phantom power shall be applied to the Input 2. Channels 3 and 4 shall be electronically balanced line-level inputs with Channel 4 including stereo RCA jacks. Additionally, the output from Channel 4 input shall be made available via an electronically balanced output with a Eurotype connector and a separate level control. Depending upon the module chosen, it can be set up for master configuration. When the input signal to an input module commands a mute function, Channels 1-4 shall be muted. Only Channel 1 shall have a continuously variable mute threshold control on the rear panel. Setting this control fully clockwise shall defeat the Channel 1 mute function. The mute level threshold for Channel 1 shall be increased as the control is turned clockwise. When the signal level in Channel 1 exceeds the mute threshold, Channels 2-4 shall be muted. Channels 1 and 2 shall include a switch to defeat its muting function. [. . . ] Copies of this statement may be obtained by contacting Peavey Electronics Corporation, P. O. Box 2898, Meridian, Mississippi 39302-2898. 4 GND +Vmod OUTP UTS 100V 70V 8 COM XFMR POWER SI GNAL ENAB LE BYPASS Power Switch SPS PA POWER SUPPLY AC Input LOOP EXT MUTE 1 PWR IN MASTER LEVEL CONTROL RV C PRE OUT V C SHD 2 LO LOW HIGH HI CH 4 OUT MU TE1 MU TE2 - + AC RECEPTACLE (120V UNIT ONLY) MASTER LEVEL +V MU TE2 THRESH INPUT LEVEL MU TE1 ACTIVE CH 2 LEVEL DEFEA T DEFEA T MU TE2 ACTIVE CH 1 LEVEL CH 3 LEVEL MUTE MUTE PREAMP PREAMP MUTE PREAMP MUTE SI GNAL SI GNAL SI GNAL SENS SENS MIC TEL MIC 24V TEL CH 1 N I - + CH 2 N I LI NE CH 3 N I CH 4 N I + + SI GNAL MOD ULE PO RT CH 1 MIC +24V + PREAMP CH 4 LEVEL CH 4 OU T LEVEL Fuse STEREO IN L G - - - - MUTE 1 MUTE 2 IN GND MIC 24V OUT + R +Vfan +Vhi +Vlo -Vhi -Vlo N L Specifications UMATM 752 MIXER/AMPLIFIER UMATM 752 MIXER/AMPLIFIER FRONT UMATM 752 MIXER/AMPLIFIER BACK FUSE Peavey Electronics Corporation · 711 A Street · Meridian, MS 39301 601-483-5376 · Fax 601-486-1678 · http://aa. peavey. com ©2002 Printed in the U. S. A. [. . . ]